Wuxi YUTONG

  Most of the hydraulic cylinder is composed of a cylinder, cylinder head, piston and  piston rod  and sealing device. The comprehensive performance of the cylinder such as pressure resistance, wear-resistance and fatigue strength, determines the service life of the hydraulic cylinder. The cylinder is usually required to withstand pressure within 20Mpa (continuous pressure), and the application of mixing and pressure can even reach 55Mpa. General hydraulic cylinder made of carbon steel or low alloy   cold-drawn steel tube , such as ST52 E355, which treated by usually used to stress annealing. The heat treatment depends on the performance of the steel after cold working conditions of the hydraulic cylinder in actual production are mostly use the following heat treatment process for processing. Stress relief annealing adopts a heat treatment process lower than the heating temperature of recrystallization, which aims to eliminate the residual stress in the steel tube ca...

  Stainless steel hydraulic cylinders are used in applications where corrosion resistance is the utmost priority with   stainless steel cylinder tube   and   piston rods . Standard cylinders are made from combinations of alloy steel, such as 1020,   1045   and   4140 , which are all susceptible to oxidation and rust in humid or wet applications. Even when epoxy painted, carbon steel cylinders exposed to surface abrasion, dents or harsh chemicals can wear away any paint, leaving exposed steel to corrode. Marine environments often require the usage of stainless steel cylinders, both onshore and offshore. Saltwater is especially damaging to standard alloy steel, which will rust rapidly when exposed to saline. Maritime cylinders used for cranes, boat lifts, davits or other machinery do well when made from stainless steel alloys. Offshore oil rigs are especially prone to aqueous corrosion, and although special construction and coatings can mitigate some oxi...

  Honed ID Tubing   also called   honed cylinder tube   or honed cylinder barrel.The honing process involves using abrasive polishing stones and abrasive paper to remove small amounts of material, to produce extremely precise ID dimensions and improved finishes. Honed tubing is ready to use for hydraulic cylinder applications without further ID processing. Honed ID cylinder tube processing: Raw Materia - Acid cleaning - Parkerizing -  Cold-drawn  - stress relieving - leveling - Saw off reject parts - Honing - Anti oil coating - Packing. Material : E355 ST52,CK45,4140,4130,4340, SCM440, 42CrMo4 ,40CrMo,34CrMo4,35Cmo, ,SS304/316,Duplex 2205,etc. Delivery Condition : BK, BK+S, GBK, NBK Type : Seamless, Hot Rolled, Cold Rolled, Cold Drawn Roughness : 0.2-0.4 u Tolerance EXT : DIN2391, EN10305, GB/T 1619 Tolerance INT : H7,H8,H9

  Induction hardening  is a non-contact process used for the surface hardening of steel and other alloys. The parts to be treated are placed inside a copper coil and heated above their transformation temperature by applying an alternating current to the coil. The   cylinder rod   is then quenched to retain the enhanced properties of the steel alloy. During this process, the   induction hardened chrome rod   core remains unaffected and its physical properties remain the same. CK45 is a medium tensile carbon steel supplied in the turned, induction hardened and straightened, precision ground, polished, chrome plated and final polished condition, with a typical base metal tensile strength of 670 Mpa, an induction hardened case of 3.2mm thick approx. to Rc55-65, plus a typical hard chrome plated surface hardness of HV 1000 - 1150.Characterised by an extremely smooth surface finish with excellent wear and corrosion resistance, supported by an induction harde...

  4140 chrome cylinder rod   is used extensively by the hydraulic cylinder and pneumatic industries, and is employed by other industry sectors for a wide range of applications requiring higher strength. 4140 is a 1% Chromium - Molybdenum high tensile steel supplied in the hardened and tempered, cold drawn or turned, precision ground, polished, chrome plated and final polished condition, with a typical base metal tensile strength of 850 - 1000 Mpa, plus a typical  hard chrome plated surface hardness  of HV 1000 - 1150. Characterized by an extremely smooth surface finish with excellent wear and corrosion resistance, coupled with a base material giving high strength and good impact properties. 4140  hard chrome plated bar  has very good machinability, similar to 4140 uncoated bar. Machining however should commence beneath the chrome plating, or at the unchromed surface at the end of the bar. To protect the polished chrome surface, soft materials such as copper...

  Honed tube for hydraulic cylinder   also work as   hydraulic cylinder barrel   in many industry.This is because honed tubes are the most important materials of manufacturing hydraulic cylinders. And as this kind of tubing is usually honed in tube inside diameter, it is known as  honed ID tubing  also. PRODUCTION PROCESS OF HONED TUBE FOR HYDRAULIC CYLINDER While producing honed tubes,  Wuxi YUTONG  uses the honing process to make smooth surface finishes of inside diameters; and to maintain exact tolerances on inside diameters. Under the honing process, abrasive stones and paper are used to the ID of the tubes, which “grinds” stock away to remove surface imperfections from the cold drawing process; and to achieve the desired dimensional tolerances and surface finish. And normally we use cutting fluids to provide easy cutting action and also to remove the cut material from the bore. WUXI YUTONG ALSO SUPPLY THE FOLLOWING TUBES AND RODS ST52 Honed T...